Training:

Relevant data for this tutorial:

Step 1: Start MSC Apex Generative Design

The program starts and you can directly create your optimisation model

Step 2: Model generation

You can either create the geometry directly in MSC Apex Generative Design or import already existing files. You can import for example .xb, .xt, .step, and .sldprt files into the program.

• Import/create the Design Space including the Interfaces (Non-Design Spaces) in MSC Apex Generative Design as one solid. For this GD-Bracket the already prepared Design Space was imported.

• Open the Optimization Tools to select the imported Geometry as the Design Space.

• Choose the material AlSi10Mg in the Materials editor and assign it to the Design Space. In this case the material behaviour is Isotropic.

• The Tension Strength is the maximum allowable stress for the material and is set to 460 MPa.

Step 3: Definition of boundary conditions

Creation of local coordinate systems to apply forces

Go to the Loads & Boundary Condition Tool to enter the loads and fixations. Displacements, Forces, Moments, Gravity and Pressure Loads can be applied using different selection options.

To apply the forces the Force Tool from the Loads & Boundary Condition Tools is needed.

Loads & Boundary Condition for Event 1

For the first Event two remote loads are created (Force 1 & Force 2) on the shown surfaces with the given values in the tables.

Force 1 is applied on the left, big cylindrical surface:

Force 2 is applied on the other big cylindrical surface:

For the first Event one Displacement constraints at the middle cylinder is created:

Under Displacement Constraints a “clamped” constraint can be chosen, which locks translations in all three directions. On the left side of the Tool the relevant geometry choice can be selected. In this case the surface of the middle cylinder is selected to attach the constraints as shown in the picture below.

Loads & Boundary Condition for Event 2

For Event 2 four loads and one displacement constraint on each side are needed.

And the same clamping loads (Load 7, 8, 9, 10) are also applied on the other side.

On both outer bigger cylinders clamped displacement constraints are applied:

Step 4: Interface Creation

Interfaces have to be created for every functional surface - so every surface where a boundary condition is applied to. With this Tool an offset to the inside with the input “Non-Design Space Thickness” and an offset to the outside with the input “Machining Allowance” is created. The Offset Distance is expanding the Interface to the set value to create material on front faces.

All surfaces on which a boundary condition is applied can be selected directly as an interface with the “Select Faces from Loads and Boundary Conditions” button. The Boundary Condition surfaces will be highlighted and can be selected/deselected. With “Apply” the Non-Design Space Thickness, Machining Allowance and if available Offset Distance values will be applied to the selected surfaces.

• In this case for the outer, bigger cylinders and the middle cylinder inclusive the front faces are manually selected. A Non-Design Space Thickness of 3 mm and a Machining Allowance of 1 mm is entered.

• Note: the Interface Offset (usually displayed in red) is not visualized due to a limitation. The correct value will be considered in the optimisation.

• On the smaller outer cylinders a Non-Design Space Thickness of 1mm and a Machining Allowance of 0.5 mm is applied. For these cylinders the “automatically create interface” option can be used by selecting the corresponding boundary conditions on these surfaces.

Step 5: Definition of load cases

The next steps are defined in the Studies area.

All boundary conditions must be assigned to the specific load cases, which are defined as Events. The number of Events can be changed by adding/deleting Events to the GD Scenario. The assignment of the boundary conditions to the Events can be made in the Loads & Constrains Window. The already created loads and constraints that concern the Design Space are listed in this window and can be activated for each Event individually.

• Event 1: Force 1, Force 2, Constraint 1

• Event 2: Force 3, Force 4, Force 5, Force 6, Force 7, Force 8, Force 9, Force 10, Constraint 2, Constraint 3

Step 6: Definition of optimisation parameters and Generative Design Settings

The optimisation parameters are selected in the Studies Area as well.

• Manufacturing Method: Generic AM

• Failure Criteria: Von Mises

• Safety Factor: 30

• Strut Density: Medium

• Shape Quality: Balanced

• Complexity Setting: 10

Don’t forget to save the project!

Step 7: Casting Design Rules via the Advanced User Settings

To change the Manufacturing Method to Casting the Advanced User Settings have to be used.

The following commands are added to the scenario:

With the first command the optimisation strategy is set to Casting. The following commands defining tools. Each tool is one draw direction. For each draw direction a draft angle can be set. The draft angle is the tapering angle for walls/ribs regarding the Draw Directions. Specified in degree.

In this case two draw directions are defined in positive and negative z-direction and a tapering angle of 5°.

Step 8: Starting the optimisation and visualize the results

If all data is correct, the optimisation can be started and tracked in the Post Processing. The Analysis Readiness function checks if all information is provided and the optimisation can start.

All result iterations are displayed as soon as they are available. Furthermore, you are able to stop the optimisation in this selection area. However, a Restart is not directly possible.

The optimisation is finished after 64 iterations (Shape Quality: Balanced).

You can check the status of the optimisation in the GD Status and get more information on Warning and Error messages. This can be done directly in the Post-Processing as well as in the Studies tab for an optimisation that has already run.

Step 8: Visualization of Stresses & Displacements

• Inside the Post-Processing the von Mises stress and the displacements are visible for all iterations and for every Event

• The Scale can be influenced individually

You can go back to the model setup by clicking the Exit button in the right bottom corner.

The whole MSC Apex Generative Design project with all results can be downloaded here:

You might also be interested in these tutorials:

• Support Reduction - Gripper