...
The optimisation has reduced nearly all material which is not a fixation or part of the symmetry plane. All remaining elements are fixated. The applied force might be too small in comparison to the stress goal which ensures the reduction of almost all the material. Please reconsider your model set up.
W6bef1a88
Low memory, reducing preallocation amount … attempts left.
Memory storage is checked. If not enough memory is available, less memory storage is checked. If there isn’t enough memory storage available to do the allocation an Error (Eb20f3210) will be occur.
W644693f8
Time estimation has become inconsistent, expect inaccuracies.
For Restarts and Two-Stage Optimisations the time estimation is inaccurate.
W5cfd1878
Solving matrix … via extern solver … failed.
Using CPU solver only
W36faacc8
Error detecting available memory / low available memory … GB
There are two possible reasons for this warning:
The available memory cannot be detected because of the operating system.
There isn’t even enough memory available to let the optimisation start.
Make sure that there is more memory available or reduce the complexity.
W4ebe0a20
… Projected memory requirement exceeds available memory - complexity … is too high. Theoretical limit: complexity … recommended: …
This is a feasibility check regarding the input complexity value. The chosen complexity value is too high to be calculated on this machine. A certain maximum complexity value is recommended.
W4ff53240
… Optimization will likely run out of memory - available … GB, projected need … absolute maximum … recommended maximum …
This is a feasibility check regarding the input complexity value. The chosen complexity value is too high to be calculated on this machine. A certain maximum complexity value is recommended.
W648041c8
Retained volumes occupy a significant portion of design space … volume 50% which increases the calculation time as well as the needed memory. Please reduce the complexity to reduce the calculation time and memory. Retained volumes will occupy about … GB of memory with current settings.
W76bd49a8
Unable to compute centroid for geometry … using bounding box center instead
A “corrupt” STL/PLY file was supplied for a Mask named in the warning text. Depending on other mask settings (whether the surface is to be used / filled), different centroids / centers of gravity are computed. This warning indicates all those attempts have failed and instead the bounding box center is used.
This can happen if the input has degenerate triangles or is not a closed surface. Please check the input files or replace these if possible.
W2e4e8b88
boundary condition is dislodged - no active elements …
A boundary condition was disconnected. A reconnect and other connection strategies were unsuccessful. Please check you model set up and make some adjustments for a feasible model.
W33559448
License feature(s) have become invalid, checking out again in … seconds.
They will be checked out again in … seconds.
W5b09c550
event … has no connected boundary conditions.
The Event … has no connected boundary conditions. The Event will be ignored from now on.
W5b820290
geometry … is not used by anything
The geometry … is not used by anything in the configuration file and will not be considered in the optimisation.
W244ee728
coordinate system … is not used by anything
The defined coordinate system … is not used by anything in the configuration file and will not be considered in the optimisation.
W41d43530
Missing density for space … setting to …
The density is set to the value listed in the warning message.
W1fb6cc10
Config entry 'calculationType' is deprecated, please use 'shapeQuality' instead.
W384d5280
Config entry 'designType' is deprecated, please use 'strutDensity' instead.
W74060730
fullPivHouseholderQr failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W760bf120
colPivHouseholderQr failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W777a0bc8
completeOrthogonalDecomposition failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W041b3b18
CG failed
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W31b28cd8
Build space geometry is not also design
This might occur while performing a Command Line optimisation. The defined build space geometry is not defined as the design geometry. Therefore, the geometry needed for the intersection is not available and thus no intersection geometry is available. Please adjust the Configuration File.
W2f07aa98
Geometry … is not used by anything
This might occur while performing a Command Line optimisation. A geometry is not used in the optimisation. Please adjust the Configuration File.
W38a529d0
Failure criterion … is not used by anything
This might occur while performing a Command Line optimisation. The Failure Criterion is not used in the optimisation. Please adjust the Configuration File.
W6c825a00
Material is not valid. Condition 1 failed for Isotropic material …
W6c825a01
Material is not valid. Condition 2 failed for Isotropic material …
W6c825b00
Material is not valid. Condition 1 failed for transversal isotropic material …
W6c825b01
Material is not valid. Condition 2 failed for transversal isotropic material …
W6c825b02
Material is not valid. Condition 3 failed for transversal isotropic material …
W6c825b03
Material is not valid. Condition 4 failed for transversal isotropic material …
W6c825b05
Material is not valid. Condition 6 failed for transversal isotropic material …
W6c825b04
Material is not valid. Condition 5 failed for transversal isotropic material …
W6c825b06
Material is not valid. Condition 7 failed for transversal isotropic material …
W6c825c00
Material is not valid. Condition 1 failed for orthotropic material …
W6c825c01
Material is not valid. Condition 2 failed for orthotropic material …
W6c825c02
Material is not valid. Condition 3 failed for orthotropic material …
W6c825c03
Material is not valid. Condition 4 failed for orthotropic material …
W6c825c04
Material is not valid. Condition 5 failed for orthotropic material …
W6c825c05
Material is not valid. Condition 6 failed for orthotropic material …
W6c825c06
Material is not valid. Condition 7 failed for orthotropic material …
W6c825c07
Material is not valid. Condition 8 failed for orthotropic material …
W6c825c08
Material is not valid. Condition 9 failed for orthotropic material …
W6c825c09
Material is not valid. Condition 10 failed for orthotropic material …
W6c825c10
Material is not valid. Condition 11 failed for orthotropic material …
W6c825c11
Material is not valid. Condition 12 failed for orthotropic material …
W6c825c12
Material is not valid. Condition 13 failed for orthotropic material …
W6493a120
The configuration file entry 'solverMaxMemory' is deprecated, please use 'complexity' instead.
W1b158cd8
Unfeasible FEM setup: Insufficient … fixed DOF.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W1e44f6f0
Implausible FEM setup: No free DOF.
The whole Design Space is fixated so no material will be reduced.
W364cd738
Implausible FEM setup: Fixation space is poorly conditioned.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W6d49ffc0
Unfeasible FEM setup: Missing fixation in one or more directions.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W207f9b58
Smoothening of Isosurface data not available for …
Please contact MSC Apex Support.
W1535d930
Intermittent file system error …
The relocation of a file did not work. The simulation will continue.
W3080a2f0
Finalizing file << fn.u8string << failed
The relocation of several files did not work.
W39837ad0
Unused config entry …
The command is incorrect or was deprecated and will be not be considered in the optimization.
W7b364d00
Resolution … and complexity … specified together - ignoring complexity.
The resolution command is higher prioritised and outweighs the Complexity input.
W25081f18
Failure criterion Von Mises is not valid. The Tensile Strength is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W0f25e2a0
Failure criterion Tsai Wu is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W7c709bf0
Failure criterion Tsai Wu is not valid. One value is lower or equal zero, or for Fxy, F_yz and F_zx not between -1 and 1 for material …
Please change the material values according to the valid material conditions.
W7b99b450
Failure criterion Tsai Hill is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W760ca740
Failure criterion Tsai Hill is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W658f5544
Adding autogenerated interface for boundary condition …
An Interface was not created for one or more boundary condition faces. For these faces an Interface was automatically generated to guarantee a satisfying result.
This will happen for every displacement constraint because the interface surface and the constraint surface do not have to be the same.
W5fa5cf20
Some events are missing preserved fixations, attempting to compensate by setting preserve on …
The optimisation will continue to run with the changes mentioned above. If these changes are not representing the model set up you anticipated, please adjust your model set up in the “Keep Non-Design Spaces” panel.
W5acd8220
...
W213b4638
FEM forces in … are zero
There are no forces applied to the design, forces are zero, point of application is fixated in the same event as the force is applied or forces were forgotten to place in one event. Please, check your model set up.
W416620d0
FEM matrix solution failed (error … fails to achieve target margin … after … of … iterations.
The FEM could not be solved sufficiently because of the model set up. Please reconsider your model set up and try again.
W4c1a8f98
FEM matrix solution failed (error … fails to achieve target margin …
The FEM could not be solved sufficiently because of the model set up. Please reconsider your model set up and try again.
W6bef1a88
Low memory, reducing preallocation amount … attempts left.
Memory storage is checked. If not enough memory is available, less memory storage is checked. If there isn’t enough memory storage available to do the allocation an Error (Eb20f3210) will be occur.
W644693f8
Time estimation has become inconsistent, expect inaccuracies.
For Restarts and Two-Stage Optimisations the time estimation is inaccurate.
W5cfd1878
Solving matrix … via extern solver … failed.
Using CPU solver only
W36faacc8
Error detecting available memory / low available memory … GB
There are two possible reasons for this warning:
The available memory cannot be detected because of the operating system.
There isn’t even enough memory available to let the optimisation start.
Make sure that there is more memory available or reduce the complexity.
W4ebe0a20
… Projected memory requirement exceeds available memory - complexity … is too high. Theoretical limit: complexity … recommended: …
This is a feasibility check regarding the input complexity value. The chosen complexity value is too high to be calculated on this machine. A certain maximum complexity value is recommended.
W4ff53240
… Optimization will likely run out of memory - available … GB, projected need … absolute maximum … recommended maximum …
This is a feasibility check regarding the input complexity value. The chosen complexity value is too high to be calculated on this machine. A certain maximum complexity value is recommended.
W648041c8
Retained volumes occupy a significant portion of design space … volume 50% which increases the calculation time as well as the needed memory. Please reduce the complexity to reduce the calculation time and memory. Retained volumes will occupy about … GB of memory with current settings.
W76bd49a8
Unable to compute centroid for geometry … using bounding box center instead
A “corrupt” STL/PLY file was supplied for a Mask named in the warning text. Depending on other mask settings (whether the surface is to be used / filled), different centroids / centers of gravity are computed. This warning indicates all those attempts have failed and instead the bounding box center is used.
This can happen if the input has degenerate triangles or is not a closed surface. Please check the input files or replace these if possible.
W2e4e8b88
boundary condition is dislodged - no active elements …
A boundary condition was disconnected. A reconnect and other connection strategies were unsuccessful. Please check you model set up and make some adjustments for a feasible model.
W33559448
License feature(s) have become invalid, checking out again in … seconds.
They will be checked out again in … seconds.
W5b09c550
event … has no connected boundary conditions.
The Event … has no connected boundary conditions. The Event will be ignored from now on.
W5b820290
geometry … is not used by anything
The geometry … is not used by anything in the configuration file and will not be considered in the optimisation.
W244ee728
coordinate system … is not used by anything
The defined coordinate system … is not used by anything in the configuration file and will not be considered in the optimisation.
W41d43530
Missing density for space … setting to …
The density is set to the value listed in the warning message.
W1fb6cc10
Config entry 'calculationType' is deprecated, please use 'shapeQuality' instead.
W384d5280
Config entry 'designType' is deprecated, please use 'strutDensity' instead.
W74060730
fullPivHouseholderQr failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W760bf120
colPivHouseholderQr failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W777a0bc8
completeOrthogonalDecomposition failed, attempting next solver
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W041b3b18
CG failed
Different methods for solving FE equation systems are being used. This one did not work so continuing to the next method.
W31b28cd8
Build space geometry is not also design
This might occur while performing a Command Line optimisation. The defined build space geometry is not defined as the design geometry. Therefore, the geometry needed for the intersection is not available and thus no intersection geometry is available. Please adjust the Configuration File.
W2f07aa98
Geometry … is not used by anything
This might occur while performing a Command Line optimisation. A geometry is not used in the optimisation. Please adjust the Configuration File.
W38a529d0
Failure criterion … is not used by anything
This might occur while performing a Command Line optimisation. The Failure Criterion is not used in the optimisation. Please adjust the Configuration File.
W6c825a00
Material is not valid. Condition 1 failed for Isotropic material …
W6c825a01
Material is not valid. Condition 2 failed for Isotropic material …
W6c825b00
Material is not valid. Condition 1 failed for transversal isotropic material …
W6c825b01
Material is not valid. Condition 2 failed for transversal isotropic material …
W6c825b02
Material is not valid. Condition 3 failed for transversal isotropic material …
W6c825b03
Material is not valid. Condition 4 failed for transversal isotropic material …
W6c825b05
Material is not valid. Condition 6 failed for transversal isotropic material …
W6c825b04
Material is not valid. Condition 5 failed for transversal isotropic material …
W6c825b06
Material is not valid. Condition 7 failed for transversal isotropic material …
W6c825c00
Material is not valid. Condition 1 failed for orthotropic material …
W6c825c01
Material is not valid. Condition 2 failed for orthotropic material …
W6c825c02
Material is not valid. Condition 3 failed for orthotropic material …
W6c825c03
Material is not valid. Condition 4 failed for orthotropic material …
W6c825c04
Material is not valid. Condition 5 failed for orthotropic material …
W6c825c05
Material is not valid. Condition 6 failed for orthotropic material …
W6c825c06
Material is not valid. Condition 7 failed for orthotropic material …
W6c825c07
Material is not valid. Condition 8 failed for orthotropic material …
W6c825c08
Material is not valid. Condition 9 failed for orthotropic material …
W6c825c09
Material is not valid. Condition 10 failed for orthotropic material …
W6c825c10
Material is not valid. Condition 11 failed for orthotropic material …
W6c825c11
Material is not valid. Condition 12 failed for orthotropic material …
W6c825c12
Material is not valid. Condition 13 failed for orthotropic material …
W6493a120
The configuration file entry 'solverMaxMemory' is deprecated, please use 'complexity' instead.
W1b158cd8
Unfeasible FEM setup: Insufficient … fixed DOF.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W1e44f6f0
Implausible FEM setup: No free DOF.
The whole Design Space is fixated so no material will be reduced.
W364cd738
Implausible FEM setup: Fixation space is poorly conditioned.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W6d49ffc0
Unfeasible FEM setup: Missing fixation in one or more directions.
Make sure that the model is appropriately fixated. A fixation needs to be applied in every global coordinate direction.
W207f9b58
Smoothening of Isosurface data not available for …
Please contact MSC Apex Support.
W1535d930
Intermittent file system error …
The relocation of a file did not work. The simulation will continue.
W3080a2f0
Finalizing file << fn.u8string << failed
The relocation of several files did not work.
W39837ad0
Unused config entry …
The command is incorrect or was deprecated and will be not be considered in the optimization.
W7b364d00
Resolution … and complexity … specified together - ignoring complexity.
The resolution command is higher prioritised and outweighs the Complexity input.
W25081f18
Failure criterion Von Mises is not valid. The Tensile Strength is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W0f25e2a0
Failure criterion Tsai Wu is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W7c709bf0
Failure criterion Tsai Wu is not valid. One value is lower or equal zero, or for Fxy, F_yz and F_zx not between -1 and 1 for material …
Please change the material values according to the valid material conditions.
W7b99b450
Failure criterion Tsai Hill is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W760ca740
Failure criterion Tsai Hill is not valid. One value is lower or equal zero for material …
Please change the material values according to the valid material conditions.
W658f5544
Adding autogenerated interface for boundary condition …
An Interface was not created for one or more boundary condition faces. For these faces an Interface was automatically generated to guarantee a satisfying result.
This will happen for every displacement constraint because the interface surface and the constraint surface do not have to be the same.
W5fa5cf20
Some events are missing preserved fixations, attempting to compensate by setting preserve on …
The optimisation will continue to run with the changes mentioned above. If these changes are not representing the model set up you anticipated, please adjust your model set up in the “Keep Non-Design Spaces” panel.
W5acd8220
Some events are missing fixations.
Adjust your model set up so that every Event has fixations in all three main directions (or local coordinate systems main direction) included.
...
Make sure that the Keep Non Design function is activated. Increase the Complexity or increase the Safety Factor.
Eb20f3980
Missing config entry …
The configuration file is missing an entry or command. Please check your entries in the Advanced User Settings or if you are using the Command Line Optimisation please check the Configuration File. You can find all commands for the Advanced User Settings here and the Configuration File here.
E0d03bf38
Unable to resolve input file name statistics.csvthe Complexity or increase the Safety Factor.
Eb20f3980
Missing config entry …
The configuration file is missing an entry or command. Please check your entries in the Advanced User Settings or if you are using the Command Line Optimisation please check the Configuration File. You can find all commands for the Advanced User Settings here and the Configuration File here.
E0d03bf38
Unable to resolve input file name statistics.csv
This may occur if an optimisation is started with Advanced User Settings with which only 1 or 2 iterations should be calculated. If this is the case please add the following Advanced User Settings commands:
schedule.level.3.subiterations.~.outputMode.OutputGeneratedSurface |
E39d2c328
unexpected error loading file statistics.csv: Unable to open input file
This may occur if an optimisation is started with Advanced User Settings with which only 1 or 2 iterations should be calculated. If this is the case please add the How to resolve this here.
schedule.level.3.subiterations.~.outputMode.OutputGeneratedSurface |
E58799450
unexpected error writing file file_name.ply:
One of the result files cannot be written. This can happen while using parallelization (default). This can be resolved by adding following Advanced User Settings commands:
...
schedule.level.3.subiterations.~.outputMode.OutputGeneratedSurface
E39d2c328
unexpected error loading file statistics.csv: Unable to open input file
This may occur if an optimisation is started with Advanced User Settings with which only 1 or 2 iterations should be calculated. How to resolve this here.
...
schedule.level.3.subiterations.~.outputMode.OutputGeneratedSurface
E58799450
unexpected error writing file file_name.ply:
One of the result files cannot be written. This can happen while using parallelization (default). This can be resolved by adding following Advanced User Settings commands:
...
process.workers = 1
E724493a8
Unable to open file … for writing
There are no privileges to access a file which is needed. Please check where the project folder is placed in which all the results are written. Network drives and cloud storage (e.g. OneDrive) are not recommended.
E3ee97ff0
supportReductionIntensity … is out of bounds 0-10.
Please adjust the Intensity value of the Support Reduction according to the boundaries.
E449a19a0
invalid supportReductionMode … expected off, passive, reactive or active.
Please set the Support Reduction Mode to one of the supported modes.
E4a364e88
missing / incompatible strutDensity setting for use with support avoidance.
If you are using the Support Reduction, you need to define a Strut Density.
W6e184ce8
Permanently shutting down soft symmetry because all dimensions have become unsalvagably asymmetric.
Eb20f33c1
LicenseConstraintException failed to acquire … count … instances of … feature
A license for the GD Engine and/or the GPU calculation couldn’t be acquiered. Please check your licenses
process.workers = 1 |
E724493a8
Unable to open file … for writing
There are no privileges to access a file which is needed. Please check where the project folder is placed in which all the results are written. Network drives and cloud storage (e.g. OneDrive) are not recommended.
E3ee97ff0
supportReductionIntensity … is out of bounds 0-10.
Please adjust the Intensity value of the Support Reduction according to the boundaries.
E449a19a0
invalid supportReductionMode … expected off, passive, reactive or active.
Please set the Support Reduction Mode to one of the supported modes.
E4a364e88
missing / incompatible strutDensity setting for use with support avoidance.
If you are using the Support Reduction, you need to define a Strut Density.
W6e184ce8
Permanently shutting down soft symmetry because all dimensions have become unsalvagably asymmetric.
Eb20f33c1
LicenseConstraintException failed to acquire … count … instances of … feature
A license for the GD Engine and/or the GPU calculation couldn’t be acquiered. Please check your licenses.
E0850d340
Attempted to write a checkpoint on unpaused job.
Restart file could not be written at this point in the optimisation. Please have a look at the prior error code which shows the primary reason for the failed optimisation.
E16808658
Legacy config format is disabled.
Please export the Scenario again (version 2022.1 or newer) to generate the supported json file format.
W2cc566c0
Fixed … reshaping error(s) - boundary violations … threshold exceeded …
Information message that the algorithm corrected some errors in the file. The optimisation continues as before.
E79aa1a40
Fractured design space - make sure the model consists of only a single, connected body.
Occurs mainly if no Interface is placed between Design Space and Retained Volume.
W31ac7fa8
Supervoxel downsampling caused … material collision(s)
Important! Multiple materials apply to one SuperVoxel (mainly because of a Retained Volume) and one of the materials dominates the element and is used for the optimization.
GPU Solving CUDA Solver Warnings & Errors
...