Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

With the Advanced User Settings the optimisation parameters can be influenced even further than the options Strut Density and Shape Quality. Furthermore, a few unsupported options are available using the Advanced User Settings like Restart and Usage of a Startspace.

Restart, Usage of a Start Space & Influencing the Strut Density

To influence the Strut Density even further, changes of the number of iterations, stress goal percentage and number of resolution levels can be made. These settings overwrite parts of the selection of the Strut DensityStrut Densityand the Shape Quality. The table gives an overview of the default settings:

General Optimisation without a manufacturing method:

Input Commands

Explanation

schedule.level.0.iterationCount = 8

schedule.level.1.iterationCount = 8

schedule.level.2.iterationCount = 8

schedule.level.3.iterationCount = 8

schedule.level.4.iterationCount = 17

schedule.level.5.iterationCount = 15

Specify how many iterations are calculated at which resolution level.

Optimisation with casting manufacturing method:

Input Commands

Explanation

schedule.level.1.iterationCount = 20

schedule.level.2.iterationCount = 40

schedule.level.3.iterationCount = 20

Specify how many iterations are calculated at which resolution level.

...

To set up these additional parameters, the Input Commands (left side of the table) need to be added to the optimisation model in the Advanced User Settings Text Field. In the picture below an example is shown. By adding these Advanced User Settings, the first (coarse) resolution level will be skipped and the optimisation starts directly at the second level.

...

Restart (Start Space)

With the Advanced User Settings a Restart is possible. A Start Space needs to be chosen with which the optimisation will re/start.

Therefore, an already optimised STL-file is needed as a Start Space. Therefore, the unit of the exported STL-file needs to be in the same unit as the rest of the model. In most cases the Strut Density and Shape Quality settings must be changed as well using the Advanced User Settings. For a restart the same resolution level and number of to be completed iterations have to be filled in.

...

geometry.StartCandidate.path = StartCandidate.stl
nonDesign.StartCandidate.geometryName = StartCandidate

Soft Symmetry

The soft symmetry is activated per default. It influences the design generation so that the part is symmetric in all three dimensions if they were symmetric in the respective dimension to begin with. This is achieved for geometrical symmetrical design spaces even without the hard symmetry constraint.

Equivalence Delta Value:

This governs how far the optimization value of two symmetric elements is allowed to differ while still being considered equivalent. In theory any value works: the higher the value the more zealously the algorithm will try to keep Soft Symmetry, possibly degrading the quality of the produced geometry compared to a non-symmetric one. The default value is 1e-1.

Attempt Soft Symmetry:

Whether or not Soft Symmetry is attempted at all can be (de)activated here.

  • off: Soft Symmetry is deactivated.

  • always: Soft Symmetry is always on.

  • dynamic: The optimisation will start with Soft Symmetry activated but turn it off once no dimension’s symmetry can be salvaged. Note that “dynamic” will never turn it back on once it has turned it off once.

Soft Symmetry Threshold:

Specifies how many asymmetric elements are sufficient for the "dynamic" setting of attemptSoftSymmetry to turn off soft symmetry. Values between 0 and 1 are allowed, where the number represents the proportion of voxels.

The default settings can be changed with the following commands:

configuration.equivalenceDelta = 1e-1

configuration.attemptSoftSymmetry = dynamic

configuration.softSymmetryThreshold = 0.3

Overhang Angle - Support Reduction

By default an overhang surface is determined if the angle falls below 45° in relation to the baseplate. This angle can be changed with the following command:

45°

schedule.prefabricated.wallAngle=45°

Maximum Thickness (Experimental Function)

Maximum thickness of a wall, strut or rib and in general all other resulting shapes. Specified in world units.

...

configuration.maxThickness= 2

Info

Currently, this is an experimental function in an early development status. It cannot be ensured to always hit the maximum thickness target or not to exceed the stress target.

Minimum Thickness (Experimental Function)

Minimum thickness of a wall, strut or rib and in general all other resulting shapes. Specified in world units.

configuration.minThickness= 2