| Info |
|---|
Goal of this tutorial
|
...
You can either create the geometry directly in MSC Apex Generative Design or import already existing files. You can import for example .xb, .xt, .step, and .sldprt files into the program.
Import/create the Design Space including the Interfaces (Non-Design Spaces) in MSC Apex Generative Design as one solid. For this Bridge the already prepared Design Space was imported.
Open the Design Space Tool in the Optimization Tools to select the imported Geometry as the Design Space. Activate the Symmetric Design Constraint and select the XZ and YZ planes to set up the symmetric optimisation.
...
If symmetry is activated, the Z-direction of the symmetry coordinate system is the build direction. Therefore the symmetry coordinate system needs to be adjusted. For this the transformation option can be changed to rotating the coordinate system with “R”. Select the red ring for rotation about the x-axis (-90°). The Z-direction shouldn’t be orientated normal to a symmetry plane. Further information regarding build direction and support reduction can be found here.
...
Create the material in the Materials editor and assign it to the Design Space. In this case the material behaviour is Isotropic.
The specific values needed are the Young's Modulus (192372 MPa), Poisson ratio (0.3) and Density (7.97E-6 kg/mm3).
The Tension Strength is the maximum allowable stress for the material and is set to 320 MPa.
...
Go to the Loads & Boundary Condition Tool to enter the loads and fixations. Displacements, Forces, Moments, Gravity and Pressure Loads can be applied using different selection options.
...
One constraint on the foot is created and attached on the Non-Design Space:
Name | Direction |
|---|---|
Constraint 1 | x, y, z (=0) |
...
Step 4: Interface Creation
Interfaces have to be created for every functional surface - so every surface where a boundary condition is applied to. With this Tool an offset to the inside with the input “Non-Design Space Thickness” and an offset to the outside with the input “Machining Allowance” is created. The Offset Distance is expanding the Interface to the set value to create material on front faces.
One Interface is created on the same surface the force is applied to. Therefore, an Non-Design Space Thickness of 1 mm and a Machining Allowance of 1 mm is entered. Now select the surface and confirm the selection (MMB)
One Interface is created on all surfaces, except the top one, of the fixation Non-Design Space. Therefore, an Non-Design Space Thickness of 3 mm and a Machining Allowance of 2 mm is entered. Now select the surfaces and confirm the selection (MMB).
...
The next steps are defined in the Studies area.
All boundary conditions must be assigned to the specific load cases, which are defined as Events. The number of Eventscan be changed by adding/deleting Eventsto the GD Scenario. The assignment of the boundary conditions to the Eventscan be made in the Loads & Constrains Window. The already created loads and constraints that concern the Design Space are listed in this window and can be activated for each Eventindividually.
Active in Event1: Force-Moment 1 and Constraint 1
...
The optimisation parameters are selected in the Studies Area as well.
Manufacturing Method: Generic AM
Failure Criteria: Von Mises
Safety Factor: 6.4 (Stress Goal: 50 MPa)
You can switch between the Safety Factor and Stress Goal in the properties panel by clicking the gear wheel.Strut Density: Medium
Shape Quality: Balanced
...
Don’t forget to save the project!
...
If all data is correct, the optimisation can be started and tracked in the Post Processing. The Analysis Readiness function checks if all information is provided and the optimisation can start.
...
All result iterations are displayed as soon as they are available. Furthermore, you are able to stop the optimisation in this selection area. However, a Restart is not directly possible.
The optimisation is finished after 64 iterations (Shape Quality: Balanced).
You can check the status of the optimisation in the GD Status and get more information on Warning and Error messages. This can be done directly in the Post-Processing as well as in the Studies tab for an optimisation that has already run.
...
| View file | ||
|---|---|---|
|
You might also be interested in these tutorials:
...